Jump to content

Blueadventures

Members
 View Profile  See their activity

  • Posts

    4,013

  • Joined

  • Last visited

  • Days Won

    75

 Content Type 

Everything posted by Blueadventures

  1. Blueadventures
    Just bumping question, are any forum members attending this course? The date should have read 2026 (My bad) 19 to 21 January 2026.
  2. Blueadventures
    If any doubt you could sit the gear wheel on a piece of thick paper and spray paint around it and post that to them to ensure correct size. Only if there is a doubt about size. Cheers.
  3. Blueadventures
    It would have been a good development to increase the cross over pipe at the time of doing the casting patterns for the intake manifolds as there is good feedback from those that do such about the smoother idle and possibility of operating at 50% power in the instance of one throttle cable / connection breaking and engine going to full power on one carby. Would have been a good change to what Rotax have there in my opinion. (I'm open / planning to increase my R ULS balance pipe i.d. size.)
  4. Blueadventures
    What fuel in use and method (Carb or injected)?
  5. Blueadventures
    What fuel in use and method (Carb or injected)?
  6. Blueadventures
    Wonder if there are applicable colour endorsements available?
  7. Blueadventures
    Try my epoxy method on an old oil bottle and see what you think about it. I've done it a few times.
  8. Blueadventures
  9. Blueadventures
    No flying this weekend with our little cyclone visit. Hope everyone in the area is safe. The effect is now between Bowen and Sarina. Should be over the coast in 3 to 5 hours.
  10. Blueadventures
    Agree, and I do it still, also when doing low rpm descents I bump rpm up to observe response then back to rpm setting.
  11. Blueadventures
    Agree, also about 9 years ago rotax altered the spec of their oil filters to be a couple of mm longer and then they would not come off with the header in place on the factory exhaust system (talking UL and ULS).
  12. Blueadventures
    It would be a mockup, my Rotax set up is similar re header to oil filter (although a bit more clearance) I cannot remove my oil filter whilst the header is in place. This is not an issue; as I replace the oil filter every second oil change (100 hrs) and remove the header as I 'Kopper kote' the ball sockets of the header to the muffler every 100 hrs. I see the mock up is tube in tube fit header to muffler and expect it would be a ball / socket type to allow slight movement for alignment etc.
  13. Blueadventures
    I was in the back, they couldn't get the engine running right so cancelled and refunded the ticket. Heard later recent o that day it had a engine issue and only just got back to the strip.
  14. Blueadventures
    What aircraft am I in here?
  15. Blueadventures
    Angus M is an old boss of mine, He in early days was a Navy Clearance diver; he is big on training, preparation, apply learnings, getting it right and a very good communicator. ATSB is in good hands.
  16. Blueadventures
    Was on channel 7 news this morning, shows high AOA before stall.
  17. Blueadventures
    Agree, maybe have a short length of rubber coolant hose ready o cap it, hose plugged one end and secured with a hose clap over threads, as a temporary fix.
  18. Blueadventures
    As Chuck Y says;- "If you can walk away from a landing, it's a good landing. If you use the airplane the next day, it's an outstanding landing." Therefore not an outstanding landing I'd say.
  19. Blueadventures
    Two injured in light aircraft crash near Noosa, Queensland, aircraft type not known at moment. A light aircraft has crashed on Noosa North Shore in difficult-to-access terrain, prompting a major emergency response involving five fire crews.
  20. Blueadventures
    You could make one in epoxy resin, I have done the following in the past. Cut a circle of stiff thin material 0.5 aluminium or plastic sheet to fit over the opening, then coat the threads and top with mould release wax ( a floor type wax or PVA mould release) {maybe try a a fibre glass repair shop or boat builder) then mix some expoy resin and thicken with fibre glass mat cut into the smallest pieces so you have a paste (between honey and peanut paste runniness). Use some plasticine to build a base area to be the bottom of the new cap (if you can't get plasticine then cut a washer like donut to be a tight fit over the thread of the container) Next apply the resin fibre mixture over the container threads and repeat a few to build up the thickness. You will have a nice cap and you can sand and neaten it up to suit. Just an idea.
  21. Blueadventures
    Ticked off my first fly for the year with an hour out to the coast and back.
  22. Blueadventures
    I'd give Peter Anson Engineering a call and see if he can make the part and at what price.
  23. Blueadventures
    Best you phone or email Maxine at RAAus with the question why Parkes and when might it be held at Narromine. No one else can answer that question.
  24. Blueadventures
    Also looks like didn't pay last landing fee and ARO is onto him / her.🙃
  25. Blueadventures
    Agree, I have no issue with a ramp check, whether it be Rego, certificate, bfr, maintenance record, release etc.
×
×
  • Create New...