Lyndon
-
Posts
688 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Gallery
Downloads
Blogs
Events
Store
Aircraft
Resources
Tutorials
Articles
Classifieds
Movies
Books
Community Map
Quizzes
Videos Directory
Everything posted by Lyndon
-
Great I will get one Lyndon
-
Done.I will buy the sensor and fit it. Can you explain why there are two. I take it at some point heat is applied to the air cleaner. Lyndon
-
Peter would you fit it . ???
-
My manual shows no sensor in the air box what so ever. Only the external one behind the seats. It does however refer to a switch that can be mounted on the dash to switch between these two sensors. Thus my question is it worth getting. My kit is over 10 years old and it may well be not a good manual like the the later ones. Lyndon
-
Thanks for the info. I have only found one sensor in my kit and have fitted to the fuselage inside near the fuel tank header tank. It looks like it's an option with what goes in the air box. I take it must be air box tempt. I will look again but in thought two lenghts were on offer for the Ariel cable lengths. Under will work well for running the cable etc Lyndon
-
I'm back on my plane. I had an accident last November on my bike. Anyway I'm all good now. Two questions. I have a female thread in my air cleaner. I take it an option for some sensor. Thoughts ??? Get it or just blank bit off. Secondly. I'm looking at my radio. The 760 that fits neatly in the dash. How much Ariel do I need to order with it and where to put the areil. Or if some one has a better idea I'm all ears. I'm not overly fussed with it as I want a cheap unit that work's ok with a pair of head sets. Lyndon
-
Atf. Sounds good and cheap. No issues with it ??? Lyndon
-
I've got it sorted. I won't be running the low voltage light. I can wire the Hobbs and volt meter separately. Thanks Lyndon
-
I will have a look in the morning. I'm led to believe there is a common terminal on the reg. Fed from the fuse which is b+. This feeds the ignition switch. I'm fitting a later style reg without the charge light. Its fed by the battery and neg. Then the two dyno wires. It stands alone from everything else. Lyndon
-
I have my wiring diagram. It states of the low voltage Waring light is blown the Hobbs and volt meter won't work. Looking at the wiring diagram I can see how this is possible. I'm not an auto electrician so can someone confirm. My reg does not have the low voltage terminal on it. Thanks lyndon
-
Sounds good. Thanks lyndon
-
I don't know if this the correct forum but. The T51 with the ls3 I believe is a VH only plane. What is the procedure for building and rego and maintaining this aircraft if it's home built. What I'm asking is it a bridge to far for Mr Average. I'm familiar with the building and flying of the RAA planes. Thanks Lyndon
-
Keep up the good work. Well done. Lyndon
-
Gday. Does anyone own or know of an x- air in or near Adelaide. I would like to have a look and get some into on the aircraft and if possible be taken for a fly. Happy to pay for running costs of course. Thanks Lyndon 0451860386
-
I have no real expierance of either but this is my opinion. If your hands off buy a new rotax. Get it serviced. Run in on unleaded. Make sure it starts well to look after the sprag. It will more than likely last the 2000 hrs just about trouble free. If you hands on get a Jab.I'm sure they are both excellent and in my experience a well looked after engine generally tells you before it stops. Lyndon
-
In stock with reg. As I just got some. Lyndon
-
I bought mine direct from desser.shipped to Compton in. Ca then in the boot of an imported car. Took a few months but was cheap. Lyndon
-
I had the same problem. It was those washers as mentioned. Also my torque tube was bent. As you went left to right it would bind and wanted to move the rear nylon bush. Lyndon
-
This reg has neg and pos from the battery. Plug two wires to any of the three terminals. Done
-
I have upgraded the reg to three phase mosfet. My engine came with an old Ducati regulator. Got a genuine one of a used r1 yamaha for about 50 bucks. ( 2007 and on) . In the bike world these are the duck guts. Once fitted on a bike all your reliability issues are fixed. The risk of buying new and a fake vs a genuine used was not worth it. Lyndon
-
I have sorted my oil pressure sender. Cheap and should fix the vibration issues. Ok I have a new phone and I can't download pics as they are to big. Will have to sort it out Lyndon
-
I'm doing the cooling system now. Both my outlets don't match the pump Or the header tank with the the straight bit of hose supplied in the kit that is quite frankly too big in diameter. I presuming the left side of the radiator goes to the header tank and the right side which is the suction side goes to the pump ??. Or are there two huge loops at the rear of the engine . Lyndon
-
I see some people use the battery lead as a negative to the engine. Then fit a larger cable for the positive. Seems like a good idea to me. Thoughts on benefits vs extra weight. If so what size cable am I looking for. Lyndon
-
My cooler has straight fittings. Is this an issue now or down the road. Everything I can see has angled fittings. Also I have do (not fit on part sf137). I'm wondering why. Lyndon
-
I will need some new connectors . I got them out ok. Where are they available. Bert flood, Jay car ?? Lyndon
