Kyle Communications

Such a simple mod too I have a EFIS so obviously i can put the level marks where I like with programming but I like to have a analogue ASI in my aircraft as a backup...and I just have the normal arcs set to my speeds but I do like that tape line right across the gauge...i will be doing that to it. Super simple idea that I am sure will save lives

Nah...all is quiet on the western front at the moment

The antenna issue with the SE2 of course will be some requirement to the specs they had to build/design the device to by the relevent FAA or CASA or the Brits. It says in their paperwork that no mods are allowed but we all all know that to get the most out of something it needs to be modified usually 🙂 if you keep the SE2 plugged into the USB supply it will stay powered and the battery doesnt go flat of course

HF...I wouldnt be to concerned about rushing out and getting a transponder thats for sure. This Class E clusterf**k will not get up because it is even too far ridiculous for even someone like CASA to approve. Save your pennies...well at this stage

Well it certainly appears so with all the reports back

Totally agree No one though has reported any real extra fuel consumption but that is because their original prop has been set up the same

Hi Bob It depends on how you setup your prop. A fixed pitch prop needs to be setup differently to a variable pitch prop. JG did his tests as per a variable pitch prop setup and this is why you see little difference between all the props he has tested. The Eprop is setup differently being fixed pitch...how it is setup is how I setup my original Bolly and how everyone I know basically...setup up their props. When you set it up like that you get much better perofmance than before with a different prop setup the same. So all things being equal the Eprop outperforms every prop so far...over 20 props now fitted and not one customer who has said it wasnt worth every cent in the extra perfomrance they have now. I cant say anymore than that really..the proof of the pudding is in the eating

Yes thats a perfect example of what can be done now with EFB and smart software writing and devices just like the SE2 This literally makes the SE2 part of a TABS device available for reasonable cost ASA surely cant be that poorly run that they can not see these potential devices will also save them time and energy when aircraft are not withing the high traffic areas

Yes I watch all of Mark Patey's videos...He is unbelievable in what he can do and achieve..then again limitless pockets almost helps you do that. Do yourself a favour Skippy and subscribe to Mike Patey's youtube channel..its worth it I have learnt a lot more about glassing and other stuff from his videos. As far as not hearing from me...some of us still actually work you know so sometimes it can be a day or two until I see whats been posted...other times I can fire back straight after you post. I do not profess to know all the maths involved all I know is what I see with my own two eyes. So yes what you think should work to your eyes and brain doesnt necessarily do so....The first time I saw the Eprop blades I couldnt believe they had the rapp that so many have given them...well so far everyone who has them now has a marked improvement in performance...so thats all I have to say on blade shapes...except for asthetics...the rest of it I leave up to much smarter people than myself

You could always stick this prop on your faeta and see how it goes 😂

Being simplistic Mode S is ADSB and is what CASA wanted introduce back in 2014

Wasnt there a mandate from CASA that all aircraft would have to be ADSB compliant by 2020. But about 2017 i think they bailed on enforcing that to some other date to be determined because the cost of everyone would be too high. So I think ADSB will be the norm eventualy anyway it is the cost factor. I know everyone was spewing about the cost back when it was first announced back around 2014/15

The other thread is where most chat is on

Yeah well cheesed off with my great idea of a quick and nasty spray booth....a squall came through late last week and destroyed the frame..folding it over the existing large carport even tough it was tied to the existing carport and tied to start pickets on the other side...it broke all its ropes and tried to go flying So after moping around and swearing at the dog who was looking at me to say..."why?..it wasnt me you fool that thought of it" So I have decided to bite the bullet and put up a carport as I actually do need another. But it wont have any sides. i will use corflute sheets 2.4 x 1.2 and attach them to the outsides when I need to spray in there. Seal the edges with duct tape. There are some nice premade steel skillion sections available and I will just sit on 2.5 mtrs steel posts anchored to the concrete and the roof will butt up to the edge of the existing large carport..all will be come clearer when I get it done. Should take a weekend or or so and it will be done. Just waiting for pricing but I dont expect it to be more that 900 bucks in bits So finally got around to finishing the steel brackets atatched to the rear of the sav fuselage so I can put it in a rotisserie to paint it. I made some angle alu brackets that attach to the fin post and tailpane mounts also on the steel frame there are 2 square sections that get bolted to the 2 lower rudder hinges...its not going anywhere. Just have to make the plate that bolts onto the 4 engine mount spots on the front. It will be ready by the time the carport is done

Yes as my footer message says = Airservices Australia

Yes its a joke..from Brisbane the E airspace finished just east of Chinchilla and just west of Blackwater...and west of Millmerran....These guys obviously dont want anything except RPT flying

To be brutally honest I really dont think any ulralight "needs" as CS prop..the cost well outweighs the advantages

How is that other build going Peter...are you finished?

You have to be carefull with rotax bottom ends...its not the bottom ends its the cases..they frett at the main bearings...you need a 2000 hr TBO engine to make sure you get the later generation case but they can still frett

Its expensive to rebuild a rotax from genuine parts. I can tell you from experience. But its 30k for a new engine...probably cost about 15 to 20k to do a rebuild using Bert Flood for parts. I just rebuilt a 2000 hr 2015 engine for the RANS S-21 but I got a lot of aftermarket parts from the USA from people I know over there. Some of the parts I had no option but to buy from Bert flood like the main slippers...6 of them..$100 each bearing half..The sprag clutch I had to buy the outer not the clutch as that is a motorbike clutch. The seal kit thats all orings and bearing seals etc can be bought here you just need to what you need. The gearbox needs to looked at with clutch and bearings changed every 1000 hrs. Water pump gasket is from a motorbike...pistons and cyclinders cost a fortune too..I fitted a big bore kit from the USA instead. I have a Smodel sav I am almost finished rebuilding and I am fitting a big bore kit to it but it only has 340hrs on it. Best way is try to find a secondhand engine ( with log books) maybe 1000 hrs or so..that will be about 10-12k

Some further information from Eprop The first version of GLORIEUSE is electro-hydraulic, with a system like Flybox in the cockpit. Thereafter, the mechanical part will be compatible with all actuator solutions. A mechanical system (for engines with hollow gearboxes) will be considered later on. No release schedule yet... We are in the middle of a test campaign and we still have technical solutions to validate. A variable pitch propeller will allow shorter take-off and a better rate of climb, but not a higher maximum speed. Ground adjustable pitch E-Props are already the fastest on very fast aircraft, as VL3, Shark, WT9... Please see here => https://blogen.e-props.fr/archives/9362/e-props-better-than-variable-pitch-propellers/

Well I have to disagree on the whistles...maybe our kangaroos are smarter up here...I have a lot of roos down the main road to my farm..they loved to jump in front or go across the road when your coming down the road. Ever since I put a set on the sportage..and now the Triton..everytime I see a roo its hopping away from the edge of the road..never across in front of me or at me. It used to happen all the time here but since using them there has not been even one time they have tried to commit suicide Steve Donald put a set of car airhorns on his savanahh as we have a lot of kangaroos always around the strip at Caboolture especially in the mornings..he gives thm a blast on the horn and they scatter away so it certainly works..its pretty load. The sav I bought back from central NSW to rebuild had a set on it too so the car horns work

The VG is only 520kg or maybe 540kg max. No upgrage to 600 at all If it is amatuer built..go for the tyres 380 mtrs??? you wont use any more than 100 to 130mtrs mtrs normally even shorter once you get better at flying it...down hill well that depends at how good you are at not following the ground down the hill before touch down. Ihave 350mtr strip at my farm and my VG XL takes off uphill in less that 100mtrs..I do have a downhill on landing in one direction but still really only 100mtrs is used Check the video about half way through is a camera angle for landing taken from outside

I spoke with Anne "the CEO of Eprop tonight and she directed me to this new page which there is the link below I gives some more info but no release date or pricing. It looks like it is motorized for this unit being tested https://aircraft.e-props.fr/glorieuse.php?language=en

First tests with the variable pitch propeller