Jump to content

rhtrudder

Members
 View Profile  See their activity

  • Posts

    454

  • Joined

  • Last visited

 Content Type 

Everything posted by rhtrudder

  1. rhtrudder
    Got the rubber wheel, clogged up pretty quick, because it’s under the wing makes it hard to soak it ,so far metho soaked rag and fingernails , been at it off and on for hours , about half way there, thanks everyone for the advice
  2. rhtrudder
    Where can I get a rubber stick
  3. rhtrudder
    Tried citrus also carby and brake cleaner , surely there’s something that would dissolve the glue but not the paint
  4. rhtrudder
    WD40 is about the only thing I haven’t tried, what is isopropanol, tried all the paint thinners , metho, turps, acetone ,tried RP7 is that the same as WD 40, my hand still sticks to it , driving me nuts
  5. rhtrudder
    Got the rego numbers, with a heat gun, removed from under the wing, now I’m stuck with the sticky glue residue left behind , tried everything to dissolve it , any ideas?
  6. rhtrudder
    My trim indicator , series of leds , is showing out of range , gaps at the bottom , over full at the top, unsure how to adjust, something to do with the trim motor in the elevator I’m thinking , any ideas, thanks , Greg
  7. rhtrudder
    Mate just bought a jab with a microair radio, for some reason the display lights up when the avionics is switched on but no frequencies show up also when he turns off the knob on the set the display stays on ,the aircraft is new , any ideas
  8. rhtrudder
    Thanks skip
  9. rhtrudder
    I wonder where Dick Smith stands on these changes
  10. rhtrudder
    Yep , did that, seemed ok, blasted off, all good, figured it must have been a stuck needle.
  11. rhtrudder
    Leaking internally, talked to wal, he seemed to think it was something caught under the needle or sinking floats, about to go flying always a worry when engine can get go you airborne and then starts to play up , not a lot of room to get back to my strip
  12. rhtrudder
    Finally finished changing all the fuel lines and filters, went flying, engine started to run rough below 4500 , managed to get back on the ground where it stopped with fuel dripping from the exhaust, towed it back to the hanger , discovered the right side carby running fuel with the pumps on , pulled it apart can’t see anything fitted it back on, seemed ok , got it started , try again but noticed the fuel pressure above .6bar map gauge 40 on take off, unsure whether the fuel pressure is running to high and forcing fuel past the needle, so I put it back down again , wondering whether something ended up in the fuel system from the new lines and was keeping the seat open ,
  13. rhtrudder
    That’s how I understood it
  14. rhtrudder
    Spot on
  15. rhtrudder
    That’s how it all works , the carby bowls are sealed and the breathers are vented to the air box which pressurises the fuel in the bowls , gives it more fuel when running in the boost range
  16. rhtrudder
    The fuel pressure has to be .25 of a bar over the air box pressure which is feed by the turbo , I bought the gauge years ago but never fitted it , it’s got the sender one side goes to fuel pressure, wet, the other to air pressure in the intake and the read out which goes to 7psi , yankee gauge, tells the fuel pressure above the air box pressure , not sure if I can t it into the balance pipe or fit it into the air box
  17. rhtrudder
    Trying to figure out whether i can plumb the differential gauge into the carby cross over tube with a T fitting or should it be getting it’s reading straight from the air box ,and then T the wet side of the senser into the fuel pressure gauge tube
  18. rhtrudder
    The spring type spread the pressure better, but I worry that they could loose their tension, my fuel lines are mostly inside the cab behind the panel last thing I want is a line coming off
  19. rhtrudder
    Next question, which are the best clamps to use on fuel hose, the spring ones you squeeze together and slide on then release or the plain old worm types which is what I have ,
  20. rhtrudder
    Thanks for that,
  21. rhtrudder
    Fuel hose replacement due on my 914, any clues on which is the best
  22. rhtrudder
    Fitted up skyecho, all registered, turned on , send young bloke up and raced inside to see him on ozrunways but not to be seen , could see other aircraft, what am I missing
  23. rhtrudder
    Since I removed the disc the vibs have gone, checked the carbs , all good
  24. rhtrudder
    Pretty sure the prop strike had nothing to do with it, been going on for months, sometimes it was good other times no so , I guess it depended where the weights ended up between flights, will cut it open and see what’s inside, I persevered not realising that was the cause but after fitting the new prop the penny dropped, I only just sold my dyna vibe figuring I didn’t need it
  25. rhtrudder
    Noticed my plane slowly developing a vibration over the last 6months , ended up replacing my prop, wheels up landing , and the vibs still there so I removed the plate and noticed it had a rattling sound which I didn’t think was there when I fitted it , now vibration has gone , if you have fitted one might pay to get a prop balance to check it out
×
×
  • Create New...