cherk

My experience has been ie:   replace incandescent bulbs with LEDs , the blink rate (frequency) goes up rapidly and requires additional (resistive ) load to slow the rate DOWN to acceptable levels . YEMV !

🤔

The additional load of the relay on the module MAY slow the rate of 'blink' !

🥴

Via AVBrief .............check out the 'REAL' wing flutter video !!!   🤪  .

The original moving map display !

2 hours ago, danny_galaga said:

3 pob. 

 

https://www.whathifi.com/hi-fi/vinyl/vinyl-records-will-be-around-forever-the-tiny-vinyl-founders-on-the-black-discs-enduring-appeal

????????????????????????????

3/32 X 1/8 , PM address 

54 minutes ago, Lyndon said:

They don't have apparently 

3/32 diam ?? 1/8 length ?? or otherway ??? might have both , hard or soft ?? AN or Avex ??

5 hours ago, FlyBoy1960 said:

I was just reading about the no-fly zone on the Internet and thought I would jump off to flight radar and have a look. Look at the flight tracking for this Etihad flight from Moscow to Abu Dhabi. It's transponder is going on and off by the look of the tracking and it is actually in around airspace. This was up-to-date as of 13:30 this afternoon.  Strange ?

 

Iv'e seen a couple of the same flight path over various times ...........Me thinks it's a protected species !!!

https://stratusbyappareo.com/wp-content/uploads/2021/12/600890-000063-Stratus-3-Pilots-Guide-FULL-PDF.pdf

IMU explained

"They" did say Cirrus ! coz everyone knows a parachute comes with a CIRRUS !🤔

And Cirrus isn't aluminium !

.....or Fishoilene .....penetrates and dries like varnish but slightly flexable

4 hours ago, cscotthendry said:

When I was about 150' AGL, the plane started an uncommanded left bank. I started to correct in the usual manner with a slight pressure on the ailerons, but the plane didn't respond as I expected it to. 

I dont quite understand trying to correct via the ailerons in that situation , where MY instinctive reaction is apply opposite rudder  . Lift the wing with rudder , "fly the wing".

( in the situation you described )

?????No mention of rudder ????

Hi Neil, just noticed you can make forks for the Savannah........can you make forks for other varieties , from dimensioned plans ??  eg: Zodiac 601 HD .

1 hour ago, facthunter said:

That's pretty weak.  Nev

Bit like the door "Plug"

3 hours ago, spacesailor said:

The HB  is built with either the Learner's wheel at front or taildrager

In this world there are more learners then ,than arse draggers , 😴with comments like that !!

just a quick (remote_ under dash ) pic of a sender in the horizontal wall of a 60 L header .

screws pre smeared before insertion !

4 hours ago, skippydiesel said:

I Ian,

 

Yes its great stuff, reminiscent (same smell and tackiness??) as most of the pre silicon sealants. I  have had the same tube of STAG in my plumbing tool box for possibly 8- 10 years - used sparingly works a treat. You think it would work around the studs on a flange mounting, as depicted previously??

Yeah , I have tubes in various stages of use for donkies !  I use it on all tube/hose fittings including fuel sender to tank seals , and mine are side mounted......no leaky...nicee.

If I get a chance i'll see if I can get a pic under the dash of one installation.

https://www.repco.com.au/car-care-panel/adhesives-sealants/adhesives/stag-joining-paste-200g-sg200/p/A7850719

works like a charm !

5 minutes ago, trailer said:

Who in Australia is doing the best price on a SkyEcho2?

I got mine via the uavionics .au , was maybe $100 lower than retailers at the time !    🤪

15 minutes ago, Carbon Canary said:

Other  than cost and weight in ELAs what are the other negatives for a BRS ?

because of the ballistics involved , there are protocols regarding the access to aircraft by rescue teams if the said ballistics have NOT been activated !!!

2 hours ago, Student Pilot said:

Anybody familiar with Bob Lazar's drawings on flying machine design? Do a bit of reading on the subject, it is interesting.

This Bog Lazar ???????

https://duckduckgo.com/?q=Bob+Lazar&atb=v314-1

AND..

what is this project address???  home ? or hangar?

   ........with thanks , O.K & Mark